Skip to content
Pickoryx

TL-SG1428PE vs TL-SG1005P: Plan Power Before Choosing Ports

Choose TL-SG1005P for up to four endpoints only after checking the revision: V1 is 802.3af with a 56 W total budget; V2 adds 802.3at support with up to 30 W per port and 65 W total. Choose TL-SG1428PE for a larger power plan or configurable power administration: its current page specifies 24 powered ports and 250 W total, while detailed recovery controls need a hardware/firmware check. Neither retailer-linked unit’s hardware revision is verified here.

Published by Pickoryx · Published 2026-10-11

Source checked 2026-10-11 01:23 UTC

Products compared

Pickoryx may earn a commission from qualifying purchases through the paid Amazon links on this page, at no added cost to you.

The buying question

Will the endpoint set fit the available PoE power, and is configurable power control worth maintaining?

A small no-configuration installation versus a larger documented power budget and configurable power administration, with hardware-revision checks for either choice.

Quick verdict

Choose TP-Link TL-SG1428PE if

  • Your verified TL-SG1428PE revision fits a plan beyond four powered endpoints or the smaller switch’s aggregate budget, with each endpoint and the concurrent total checked.
  • You need configurable power limits, priorities or readouts and will maintain the applicable settings and recovery exceptions.
View TP-Link TL-SG1428PE on AmazonPaid link

Choose TP-Link TL-SG1005P if

  • Four or fewer endpoints fit a confirmed V1 802.3af/56 W configuration or confirmed V2 802.3af/at, 30 W-per-port/65 W-total configuration, with headroom.
  • Plug-and-play power distribution meets your needs; you do not need the configurable power workflow described here.
View TP-Link TL-SG1005P on AmazonPaid link
When the recommendation changes
  • An endpoint needs a different PoE standard or more allocated power than the chosen revision allows.
  • The simultaneous total, including headroom, exceeds the chosen budget.
  • The seller cannot confirm the revision needed, or the required management controls do not apply to its hardware and firmware.

The differences that matter

Revision Conditional Endpoint And Concurrent Power Eligibility

TP-Link TL-SG1428PE

The current TL-SG1428PE page specifies 24 PoE+ ports, 802.3af/at, up to 30 W per powered port and 250 W total. These figures do not establish every hardware revision.[1]

TP-Link TL-SG1005P

TL-SG1005P V1: four powered ports, 802.3af and 56 W total. The V2 page: four powered ports, 802.3af/at, up to 30 W per port and 65 W total. The offered hardware revision is unverified.[2, 3]

What this changes: Check each endpoint’s required PoE standard and switch-side power allocation, then add concurrent allocations with headroom. Port count is not simultaneous full-power capacity: 4 × 30 W = 120 W exceeds the V2 budget; 24 × 30 W = 720 W exceeds the current TL-SG1428PE budget. These are ceiling calculations, not measured delivered power or compatible-device counts. TP-Link says the 65 W and 250 W budgets are lab-based and actual budgets vary with clients and environmental factors.[1, 2, 3]

The better fit depends on your priorities

Configurable Power And Recovery Maintenance

TP-Link TL-SG1428PE

Web/utility management is documented. The Easy Smart guide associated with V3 support describes system and port power limits, port enable/disable, priority and live power readouts for TL-SG1428PE. Its recovery workflow needs the correct powered-device IP address and both global and per-port enable. Confirm hardware and firmware applicability before buying for these controls.[1, 4, 5]

TP-Link TL-SG1005P

Both V1 and V2 pages describe setup without configuration; the V2 page identifies TL-SG1005P as unmanaged. Automatic recovery capability is not established by the reviewed material.[2, 3]

What this changes: Choose configurable power administration when you need to set allocations, choose priority and inspect power use, and someone will maintain the settings. For the guide’s recovery workflow, maintain correct endpoint addresses; it recommends the same subnet and, with 802.1Q VLAN enabled, the powered device in the port’s default VLAN. Disable recovery on the affected port during powered-device firmware upgrades. The guide warns that a wrong IP can cause continuous rebooting.[1, 4, 5, 2, 3]

The better fit depends on your priorities

Best for your routine

A small, known endpoint set needing basic PoE power

Best fit: TP-Link TL-SG1005P

Based on listed features, not comparative testing.

TL-SG1005P is a fit when no more than four endpoints meet the confirmed revision’s protocol and power limits: V1 802.3af/56 W total, or V2 802.3af/at up to 30 W each and 65 W total. Accept its smaller aggregate budget; do not substitute a 65 W listing title for revision verification.

View TP-Link TL-SG1005P on AmazonPaid link

A larger PoE plan with an operator for power administration

Best fit: TP-Link TL-SG1428PE

Based on listed features, not comparative testing.

TL-SG1428PE’s current specifications and configurable power workflow suit this requirement if the offered hardware/firmware matches the needed capabilities. The trade-off is maintaining allocations, priorities and, if enabled, recovery addresses and upgrade exceptions. Its port count still does not permit every port to draw 30 W simultaneously.

View TP-Link TL-SG1428PE on AmazonPaid link

Value and trade-offs

One or both observed offers have eligibility conditions, so no unrestricted price difference is shown.

Pay more for capacity your checked endpoint plan actually needs or configurable power controls you will use. A bigger port count alone does not justify the premium for a four-device plan that fits the verified smaller revision.

There is insufficient verified price history here for a buy-now or wait recommendation.

Limitations

  • The hardware revision of either retailer-linked unit has not been confirmed. TL-SG1005P’s model name does not establish V2 or a 65 W budget; do not apply the current TL-SG1428PE specifications to every older revision.
  • The detailed power/recovery workflow is drawn from an Easy Smart guide reported with TL-SG1428PE V3 support. Confirm that it applies to the hardware and firmware you will receive. The original support-page link to that guide was not independently verified.
  • Published budgets are ceilings for planning, not a guarantee of power delivered to each endpoint. The manufacturer qualifies the current 65 W and 250 W budgets by client limitations and environmental factors.
  • No hands-on, head-to-head performance or long-term reliability testing was performed. Automatic recovery is a configuration feature, not evidence of fewer outages. TL-SG1005P recovery capability remains unverified.

Questions shoppers ask

Can every powered port supply its advertised maximum at once?

No such capacity follows from the per-port figure. Four ports at 30 W would total 120 W, above the TL-SG1005P V2 page’s 65 W budget; 24 at 30 W would total 720 W, above the current TL-SG1428PE page’s 250 W budget. V1 TL-SG1005P instead has a 56 W 802.3af specification. Use the endpoint’s required switch-side allocation, not only its typical running consumption, and keep headroom within the verified revision’s limits.

What should I record before ordering?

List each endpoint’s PoE standard and required allocation at the power-sourcing switch, then total the simultaneous requirements. Ask for the offered switch’s hardware revision. If you need PoE+ or a budget above 56 W, do not assume an unspecified TL-SG1005P is the documented V2. If TL-SG1428PE recovery controls drive the purchase, also check the applicable firmware and guide.

What does maintaining the documented recovery feature involve?

For the Easy Smart workflow associated with TL-SG1428PE V3 support, enable recovery globally and on each intended port, and enter the connected powered device’s correct IP. The guide recommends keeping switch and powered devices on the same subnet; with 802.1Q VLAN enabled, the device should be in the port’s default VLAN. Update these settings when addresses or network layout change. Disable recovery on the affected port before updating the powered device’s firmware: the guide warns of device damage during upgrades and continual rebooting if the configured IP is wrong. Check hardware/firmware applicability first.

Methodology and sources

Compared revision-specific published PoE limits and documented power-management procedures. The capacity examples are arithmetic from published ceilings, not measurements.

AI assisted source research, drafting and editing. Pickoryx did not conduct hands-on testing of these switches.

View 5 sources
  1. 1.TP-Link TL-SG1428PE product specificationsTP-Link · Official specifications · Source checked 2026-10-11 01:22 UTC
    Evidence used on this page
    • Dedicated 24 PoE+ Ports; Making Management Easy; hardware and management specifications; budget footnote: Current page: 24 powered ports, 802.3af/at, up to 30 W each and 250 W total; web management and recovery; actual budget caveat.
  2. 2.TP-Link TL-SG1005P V1 specificationsTP-Link · Official specifications · Source checked 2026-10-11 01:23 UTC
    Evidence used on this page
    • Overview; Intelligent Power Management; PoE Ports: V1: four 802.3af powered ports and 56 W total; no configuration required.
  3. 3.TP-Link TL-SG1005P V2 product pageTP-Link · Official specifications · Source checked 2026-10-11 01:22 UTC
    Evidence used on this page
    • Dedicated 4-Port PoE+ Switch; Plug and Play; PoE Ports; budget footnote: V2 URL: four 802.3af/at ports, up to 30 W each and 65 W total; unmanaged, plug and play; actual budget caveat.
  4. 4.TP-Link Easy Smart Switch User GuideTP-Link · Official specifications · Source checked 2026-10-11 01:22 UTC
    Evidence used on this page
    • Chapter 7, sections 7.1–7.3: PoE Config applicability, limits and Auto Recovery: Names TL-SG1428PE for PoE configuration; power readouts and priority; IP-ping recovery with global/port enable and firmware-update and wrong-IP warnings. Hardware/firmware applicability must be checked.
  5. 5.TP-Link TL-SG1428PE V3 download pageTP-Link · Official specifications · Source checked 2026-10-11 01:22 UTC
    Evidence used on this page
    • Hardware version V3; Manual list: V3 support lists Easy Smart Switch User Guide. Does not establish that a retailer supplies V3.

Continue comparing